I recently bought a used GTP-500 with no remote included and I would really like some help from you guys here please.
I have a Vizio vur8 remote and it has a jp1.3 6 pin on the back.
I tried several things like the 990 and 991 commands but did not work, please help.
help with Adcom GTP-500 pre amp
Moderator: Moderators
Use Setup code Audio 1530 and the EFCs listed in this older thread about the GTP-500. Note that the GTP-500II uses a different IR protocol, so make sure that you've got a 500.
To add the EFCs to your VUR8, use the 994 command.
1) Tap the Audio button
2) Hold the Setup button until 2 blinks
3) Enter 994
4) Tap Setup (don't hold it)
5) Enter the 5 digit EFC
6) Tap the button you want to assign the function to.
The remote should blink twice.
To add the EFCs to your VUR8, use the 994 command.
1) Tap the Audio button
2) Hold the Setup button until 2 blinks
3) Enter 994
4) Tap Setup (don't hold it)
5) Enter the 5 digit EFC
6) Tap the button you want to assign the function to.
The remote should blink twice.
-
The Robman
- Site Owner
- Posts: 22008
- Joined: Fri Aug 01, 2003 9:37 am
- Location: Chicago, IL
- Contact:
Here are the codes:
00240 = 1
00080 = 2
00144 = 3
00017 = 4
00006 = 5
00030 = 6
00238 = 7
00034 = 8
00242 vol up
00082 vol down
00015 Power
00142 Source
00078 FM/AM
00146 Tune Up
00019 Tune Down
00240 = 1
00080 = 2
00144 = 3
00017 = 4
00006 = 5
00030 = 6
00238 = 7
00034 = 8
00242 vol up
00082 vol down
00015 Power
00142 Source
00078 FM/AM
00146 Tune Up
00019 Tune Down
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
-
wormsdriver
- Posts: 3
- Joined: Sun Apr 09, 2017 5:57 am
First of all I want to thank you guys very much for your help. Second, I'm a bit embarrassed but how do I input setup code Audio 1530? Do I need a jp1 cable?3FG wrote:Use Setup code Audio 1530 and the EFCs listed in this older thread about the GTP-500. Note that the GTP-500II uses a different IR protocol, so make sure that you've got a 500.
To add the EFCs to your VUR8, use the 994 command.
1) Tap the Audio button
2) Hold the Setup button until 2 blinks
3) Enter 994
4) Tap Setup (don't hold it)
5) Enter the 5 digit EFC
6) Tap the button you want to assign the function to.
The remote should blink twice.
-
wormsdriver
- Posts: 3
- Joined: Sun Apr 09, 2017 5:57 am
-
The Robman
- Site Owner
- Posts: 22008
- Joined: Fri Aug 01, 2003 9:37 am
- Location: Chicago, IL
- Contact:
Here's a user manual, in case it helps
http://pdfstream.manualsonline.com/b/b7 ... 3f99fb.pdf
http://pdfstream.manualsonline.com/b/b7 ... 3f99fb.pdf
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!