Nevo C2 issues

captainjrl · Post by **captainjrl** » Wed Oct 26, 2016 10:22 am

So I bought a Nevo C2 on eBay and am having issues with it. Whenever I get started with it connected to the EX-RC.com website when I get to the point where I am told to disconnect it and follow the on screen directions I get a blank, but lit up LCD screen with no instructions. I also get this screen when trying to manually program it without a connection to my computer. I've tried the battery removal and number press reset to no avail. I have contacted the seller, but shipping it back will be relatively costly. Any sugestions?

mdavej · Post by **mdavej** » Wed Oct 26, 2016 10:48 am

You can skip that part. When asked if you want to test the commands, answer no.

If you're running Windows 10, you also have to do this for it to connect properly:
http://www.hifi-remote.com/wiki/index.p ... quirements

It may be stuck in a firmware update loop. The above should get you past that as well.

Here's another reset procedure to try (#p10) :
https://www.hifi-remote.com/forums/viewt ... 7215#p27215

captainjrl · Post by **captainjrl** » Wed Oct 26, 2016 8:53 pm

OK. So I was able to get the reset accomplished and manually program in my devices. Now I am trying to setup my Activities, but that is requiring me to use the EZ-RC website. When I try to upload my devices from the remote to the website, it does not happen. No error messages or anything. Any ideas?

mdavej · Post by **mdavej** » Thu Oct 27, 2016 7:56 am

What operating system?

captainjrl · Post by **captainjrl** » Thu Oct 27, 2016 9:27 am

Windows 10.

mdavej · Post by **mdavej** » Thu Oct 27, 2016 10:49 am

You must do the registry patch I linked above. Have you done that?

captainjrl · Post by **captainjrl** » Thu Oct 27, 2016 10:56 am

I did it manually before and verified before I tried to connect again that is was still set to 0.

However I tried to use the patch and got an error, but my registry was already updated and I'm not sure if that is what caused the error.

mdavej · Post by **mdavej** » Thu Oct 27, 2016 11:26 am

When you go to ez-rc, do you "Open with Internet Explorer" from Edge?

Are you open to using Remote Master instead?
http://www.hifi-remote.com/wiki/index.p ... rogramming

captainjrl · Post by **captainjrl** » Sat Oct 29, 2016 12:39 pm

I was using IE not Edge, but it was IE11. I switched to IE8 using the developer options and it seems to be connecting now.

I am open to using remote master, but need a tutorial. Something a little more substantial than what was listed.

Also, my TV and AV Receiver seem to be missing essential commands in order to setup Activities correctly (specifically the necessary inputs). I tried to have the remote learn the keys from the original remotes but can't get that to work.

mdavej · Post by **mdavej** » Sat Oct 29, 2016 6:59 pm

Hmmm... the tutorial is pretty detailed and even has a new Nevo section. Where exactly are you getting hung up?

To help with your TV and A/V inputs, we'll need model numbers.

Learning works fine. But you have to exit ez-rc and upload after each learning session or your learns will get deleted.

Glad you got it to work with IE8, but it should work fine with IE11. Works for me on about 5 different computers.

captainjrl · Post by **captainjrl** » Sun Nov 06, 2016 12:43 pm

I found the turotial after looking a little more carefully and will give it a go.

The model numbers are:

Samsung TV is HLS6187WX/XAA
Yamaha AVR is RX-A850

Thanks

mdavej · Post by **mdavej** » Sun Nov 06, 2016 2:30 pm

Here are some files that should work for you:

TV: https://www.hifi-remote.com/forums/dload ... le_id=6876
AVR: https://www.hifi-remote.com/forums/dload ... e_id=13141

captainjrl · Post by **captainjrl** » Sun Nov 06, 2016 4:00 pm

Those seem to be working great. Thanks a bunch. I think I may need an upgrade code for my DVD player. Can you help with that one?

Sony BPD-BX510

mdavej · Post by **mdavej** » Tue Nov 08, 2016 9:12 am

Sorry, missed your reply. This will work for your BD player:

https://www.hifi-remote.com/forums/dload ... e_id=10211

captainjrl · Post by **captainjrl** » Fri Nov 11, 2016 12:22 pm

Thanks. Now I need some help with setting up my activities with RMIR. I'm having issues with getting the commands figure out so that when I switch between activities my TV and AVR are not powered down. Suggestions?

EDIT: The code for the TV seems to be off, when I program an activity to set the HDMI to HDMI1 it sets it to HDMI2